Muzzle threading on KIDD tapered rifle barrel

KIDD .22LR Black Tapered Rifle Bull Barrel

0 Review(s) Write a Review

Your Price: $325.00

.22 straight tapered barrel

MFN: 101-2

Availability: In Stock

finish & muzzle threading options *

Quantity

Description

Aftermarket barrel for the 10/22®
starts at .920" tapers to 0.700" at muzzle
20" length, 2 3/4 pounds
Sets in a bull barrel stock channel
1/2" at 50 yards 5 shot group guarantee

Try our 20 inch Chrome Moly straight taper barrel, that slips into your 10/22® receiver. Our straight tapered barrel is not as small at the muzzle as the factory taper, because we found that amount of taper to negatively affect the barrel's accuracy abilities. With a .700 muzzle we can still guarantee a 1/2" group at 50 yds. Even though this is a 20" barrel the balance point for the rifle is very close to the shooter's body due to the taper.

We believe these are the finest barrels on the market, each one is hand lapped. Our Chrome Moly barrel is bored and rifled by Lothar Walther in Germany. Tony Kidd then performs all the final machining to make our match barrel a worthy KIDD product. A proprietary chamber reamer is used to ensure the cartridge and bullet feed smoothly. Our barrels are chambered to accept .22 LR ammo and have a 1:16 twist. Our muzzle threading is 1/2"-28 and is available with a protective cap.

The unique convex extractor slot eliminates extraction problems by ensuring the extractor is always in perfect alignment with the case rim. Why doesn't everybody use this extractor slot? Because the tooling is very expensive and requires tolerances be held very close for proper machining. Each barrel receives an 11 degree crown and the double ring at the muzzle end with KIDD marked on the barrel.

We can offer such a great price on this barrel because we don't sell to distributors, only retail and dealer pricing are offered, therefore we don't have to increase our price to compensate for 3 tier pricing. There are cheaper barrels out there but as with all KIDD products, "you get what you pay for."

Avoiding "barrel droop":

First and foremost barrel droop is eliminated with a solid fit between the barrel and the receiver. If the barrel slips in too easily then the shooter should already be aware that there is not a secure fit and gravity will start doing her work immediately. Or if the barrel tenon is not the same diameter throughout the length then a teeter totter effect is set in motion. For instance if the breach end of the tenon is smaller then the shoulder end the weight of the barrel will "pull" the barrel down and barrel droop is created. Or if the breach end of the tenon is larger then the shoulder end then as the tenon is installed in the mortise the breach carves a larger hole and again a teeter totter effect is created as the smaller shoulder end of the tenon sits is a hole that is too large. This same effect would happen if the middle of the barrel tenon was enlarged.

KIDD eliminated barrel droop with the utilization of a resistance fit in this mortise and tenon joint, meaning that the KIDD barrel tenon is just slightly larger in diameter than the KIDD receiver mortise and we make absolutely certain that the tenon is the same diameter throughout the length.

Another problem area to be aware of is the proper utilization of the shoulder. If the shoulder of the barrel does not set flush against the receiver then again the support isn't there. Comparable to setting down a tall glass with a convex bottom, it wants to tilt. We make certain that the shoulder created between the .920" diameter and our tenon is precise. This requires specialty cutting tools to create a very clean step. But if done with less care there will be a ramp rather than a step between these two differing diameters. This ramp will not support the necessary weight and will prevent the shoulder of the barrel from sitting flush against the receiver.

When this barrel fitment is secure we recommend the v-block screws just need to be snug, around 10 inch pounds, which is just snug enough to keep the barrel from moving forward, but not too tight to pull the barrel out of alignment.

Barrel installation:

Depending on your receiver, if there is paint build up in the receiver mortise be sure to scrape that out. We recommend using an anti-seize compound to assist in installation. Anti-seize is readily available at automotive stores. It is best if you can get the barrel tenon started into the receiver mortise, then turn it over and tap the back of the receiver with a rubber mallet. Be sure to line the extractor slot up as you are installing the barrel. Your barrel is ready to shoot, just run two magazines through it before you really start looking at group size. Do this each time you change brands of ammunition as well. Keep the chamber clean, but don't clean the bore too much you will decrease accuracy. Depending on the ammo, clean the bore around every 500 rounds.

Tapered KIDD polished stainless steel barrel

KIDD .22LR Tapered Stainless Steel Rifle Bull Barrel

$314.00

Select Options

In Stock

Stainless steel bull barrel in polished or bead blasted finish

KIDD 22LR Match Stainless Steel Rifle Bull Barrel

$242.00

Select Options

In Stock

Top: Black Polished Bull Barrel Bottom: KIDD Bead Blasted Black Barrel

KIDD .22LR Black Bull Barrel

$253.00

Select Options

In Stock

KIDD .22LR Black Tapered Rifle Bull Barrel

Choose Options

Related Items